Leaderboard

(lineage-18.1-20210419-nightly-pro1-signed.zip on April 5 security patch installed smoothly using adb sideload and MindTheGapps-11.0.0-arm64-20210328_143848 )

Oh what a mess! When DPD claims they delivered the parcel to FxTec, and FxTec claims the never got it. It should be DPD that has to provide a receipt from FxTec on them recieving the parcel. If DPD are not able to produce that, it should be their responsibility. If they can produce a receipt then it is FxTec that has the problem.

Another update... so my last experiment failed, problem came right back after 24 hours. However, re-reading what @vvv was saying about the PCB flex, I tried adding a little tape to the hold the PCB down rather than padding the connectors. Seems like this one did the trick, it hasn't gone crazy for more than a day. One little symptom remain though, is that "strip" of display where it dances on when it goes crazy, isn't as sensitive anymore. More specifically, sometimes it misjudges a swipe as a tap, accidentally activating the item there. This does bring a lot of validity to say the proble

It may happen it gets worse when something touches / bends the wide flex cable coming behind the screen at the bottom short edge (top in the photo earlier). What I know is Pro1's top frame was made of plastic while Elephone's top frame is metal. ...but I don't think that is a problem, although I would be more happy if the outer curved part was metal. Also, the bottom part of the frame assembly is metal with fixing screws, I don't think it really moves inside if the glue fixing the display does not loosen. However, if the glue loosens around the screen, especially at the lower sid

If I remember well, I have only read issues with replaced displays having problems after a short while (not touch related but vertical lines appearing which may also be a cable issue anyway). These are about displays ordered from Ali / Ebay. So that may also be caused by bad quality displays or even not properly replaced ones. I have not found general issues anyway - also I do not know why some of these displays were replaced, so anything other than physical issue (also I read a lot more of Pro1 than Elephone). Moreover, I don't know if we may call it a general issue with Pro1

This actually explains why sliding your finger on the bottom it might trigger the problem. Now I'm curious if everyone is having the problem at the same exact location, which could indicate a recurring problem caused by a particular flaw in the design.

OK, I've edited the post after reuploading the images to Imgur. Seems like the forum has some problems when you're just copying/pasting an image.

I am not sure if it already had come to notice here in this forum: There is a funding campaign to have a professionally skilled developer working on Anbox container for Ubuntu Touch: https://gofund.me/acb31504 I think it is worth to be supported. Anbox is kind of a container running an android environment so that native android apps could be run. Of course this could be more convenient than dual boot 😉 Cheers, Ulle

YES!!! See attached video file (sorry for the ridiculous video quality ... had to shrink 2min to 2MB ...) I now have Ubuntu Touch via "Slot A" and LineageOS 18.1 via "Slot B". Dual boot procedure takes to get used to: It's not choosing OS during boot, instead it works from fully booted OS and then "OK, reboot into the other OS". The app used for that is "Switch My Slot" , with existing versions for UBports (Ubuntu Touch), Android and Sailfish. Feels like ages ago having such a satisfying moment like seeing this on my Pro1 \o/ Cheers, order#10248 Edit: Video is

I am also having problems with the audio being distorted while making a phone call. Pro1 with Android 9

Do you mean it seems to work if you don't tighten the screws for example or until a point it gets contact with the metal part of the phone itself? Anyway, when I have removed my screen from its frame, I have noticed some dust (relatively huge amount of pocket dirt) could go in at one of the shortest sides, which may or may not affect ghosting a bit. However, that line you mentioned which was less sensitive after this ghosting has appeared was also exists for me even when ghosting was not actually present.

The part I still find very odd is that, the screen works perfectly fine if I don't mount it to the phone chassis. I couldn't tell what is being affected when it's snapped to the frame.

For me (along with some others), only the screen was replaced, so the PCB itself was not changed but replacing the screen has resolved the issue. Also, all of us have started to experience the very same symptoms at the very same position and very same kind of ghost touches. My ghost touches became better when I have pressed the bottom left or maybe bottom right corner in portrait orientation. However, what you write sounds interesting... ...somewhere it seems to be caused by a connection or breakage issue, which may be even at the flex cable, the connector, or the display itse

Just an idea: Find a different cheap phone (possibly used with broken display) that also supports LineageOS, and try to build roms for that. when you feel comfortable doing that, you could switch to your Pro1

Yes, I've done it twice already. It's not that hard as it seems. Now if you look at my phone, even very close, you can't say the screen was swaped. Also I've installed small difusor for the notification led so now light is in one solid color.

In the Netherlands there are organisations where you can file a complaint when there is a dispute and/ or lack of service. My issue lies with both DPD and FxTec. According to DPD NL I should contact FxTec and according to DPD UK, FxTec should take actions. We all know where this is going, and has been going for months now. Asking FxTec for help hasn't resulted in anything apart in a thank you for co-operating (WTF!?). So I tried filing a complaint with DPD UK. Here is where it gets 'funny'. DPD UK still refer to the EU consumer board when you have a dispute. But, since the UK is no longer a me