Leaderboard

Google pay working here with magisk v24.3 for some time already and works on LOS 19.1 too. -Zygisk mode on -Enforce denylist -Put com.google.android.gms and com.google.android.gms.unstable to denylist under google play services. You might need to check show system apps from the denylist donfiguration settings -You manually need to download and install MagiskHidePropsConfig and do the edit device fingerprint, probably no need to do this if you upgrade from v23 and have already done this. -make sure play store says device certified, if not try clearing play store and pla

It seems that LineageOS 19.1 will be available soon for Pro1: https://www.lineageoslog.com/19.1/pro1 More information: https://lineageos.org/Changelog-26/ (F(x)tec Pro1 mentioned) https://download.lineageos.org/pro1 I hope it'll fix the charging issue I've had with the LOS 18.1 🙂

Indeed. Or at the least that there were a simpler option than an entire flash to stock, package by package to both to a and b, as the guide describes...

The charging bug is still here in LOS 19.1, according to @EskeRahn. This acredite a hardware problem with the battery regulator, I know I can charge twice before reboot, the first and second time it drops in maximum 10-15 minutes, the third time I will have to reboot as it doesn't charge anymore. This happens a few time and begins one year ago but it's worse now. On the other hand I used LOS16 without problem, but the battery was not so old. But....Interesting fact, it's charging without problem to 100% when the phone is off. edit : I'm pretty sure there was no charging bug in LOS1

Darn, that was my single wish for 19.

A wish: When password is required (e.g. after a boot), it would be great if opening the keyboard also did what swipe up do, so we can start typing the password immediately. Though this in theory is a general LineageOS request, the usage is currently very much limited to the Pro1, and perhaps a few others....

Decided to upgrade now because i must at somepoint anyway. First impressions are good, everything seems to work with magisk v24.3 and MindTheGapps. The extra dim mode is very very welcome with the pro1, now i can finally get the screen brightness to a reasonable level in dark.

Be aware that you need to upgrade to magisk 24 for Android 12 support. No need to fear the new changes, it still works all the same than before. Zygisk+denylist is basically the same than former magiskhide. Any external modules have to be manually installed f.ex. MagiskHidePropsConfig, but they work normally.

UPDATE: Installed and working 😁 Including MindTheGapps (Unfortunately OpenGapps is not available for android 12.0 yet) My data and apps was preserved nicely 🙂 BUT two of my most used apps no longer work. 😞 Greenify and Android Assistant does not seem to be allowed to fake clicks to stop the loaded bloat any more 🤬. They DO both open the dialogues, and if I do the clicking for them, then they sort of work. But the positive side of maiming that vital functionality is that Ctrl+Space (Language swap) now works again... (but it did co-exist just fine with Greenify earlier on LineageOS

Yes, it is. Actually my saga is longer and more convoluted. I had a cracked screen. Installed a new one like I did last year. Touch wouldn't work at all (like last time). Not only the edges but no touch is registered. I then went back to stock to see if the touch issue would be fixed. No dice. Plugged in a keyboard and mouse and tried to set up the stock firmware because I read that an OTA update might for stock solve the touch issue -- read it here: However, stock would show 'no updates'. But when configuring the device I realised that Google asked me to confirm on my other devices

I successfully installed LineageOS19.1 20220502 with MindTheGapps 12.1.0 20220416, but I can't get past the welcome screen setup part. After it asks me for the PIN or lock pattern it takes me to the fingerprint setup. As soon as I finish the fingerprint setup it enters a loop, asking me again for the PIN or pattern and taking me through the fingerprint setup all over again.

Well, got it apart today... Found what appears to be a manufacturing defect... The sheet metal clip holding all the ribbon connectors on to the main board was installed in such a way it had partially cut the battery ribbon cable right at the connector... Looks like I need a new battery as well... I'm not sure if the battery is still providing power to the board or not... Reseated the ribbon cable to the USB board at both ends... No change... Will not charge or boot. Disconnected the USB board ribbon cable and tried to boot. Did not boot... While testing charging, I notic

Please let us know if your charging problems change when running LineageOS 19. The official procedure for opening a bug report (at https://wiki.lineageos.org/how-to/bugreport) is still the best way we have to track problems, so please open one if you have new info to report. As far as we have been able to tell, the charging issue is triggered as the device ages, and two LineageOS developers have now reported similar problems. This is difficult to nail down however, as there are no new Pro1s being made that might be free from charging trouble with the latest software. However, our oldest d