EskeRahn 5,460 Posted February 6, 2020 Share Posted February 6, 2020 A cheap tablet holder like this would also do the trick, looks a little huge if used closed. But if opened in a flip case it is just fine. Quote Link to post Share on other sites
brunoais 334 Posted February 7, 2020 Share Posted February 7, 2020 I don't have the phone yet but I intent to use the one I already own. It can rotate indefinitely and it can optionally grab just the main body while keeping the screen loose Quote Link to post Share on other sites
EskeRahn 5,460 Posted February 7, 2020 Share Posted February 7, 2020 1 hour ago, brunoais said: I don't have the phone yet but I intent to use the one I already own. Nice. Does it have some support plate that can swing out at the bottom? Otherwise it will have to hold quite firm for it not to slip down during small bumps and vibrations while driving? Quote Link to post Share on other sites
brunoais 334 Posted February 7, 2020 Share Posted February 7, 2020 8 hours ago, EskeRahn said: Nice. Does it have some support plate that can swing out at the bottom? Otherwise it will have to hold quite firm for it not to slip down during small bumps and vibrations while driving? It holds the phone firmly. To avoid sliding, it has rubber in 3 places. Both clamps and the back. Those stripes on the holders and stripes on the back are soft ("sticky") rubber. 1 Quote Link to post Share on other sites
altwouss 22 Posted March 17, 2020 Share Posted March 17, 2020 @Rob. S. What did you end up using? Quote Link to post Share on other sites
Rob. S. 1,661 Posted March 17, 2020 Author Share Posted March 17, 2020 4 hours ago, altwouss said: @Rob. S. What did you end up using? Unfortunately, I still don't even have the phone... My plan is to try the 711042 Brodit holder I already have, as the period for returns is long since over, and if it doesn't work out, I'll order the 511309 Brodit holder, too. Quote Link to post Share on other sites
wilhelmfitzpatrick 47 Posted March 17, 2020 Share Posted March 17, 2020 Here's what I wound up with that is working quite well: https://www.xmpow.com/collections/car-phone-mount/products/mpow-127-gravity-car-phone-mount-air-vent-phone-holder I like the gravity style holder for quick placement and removal. It seems to be available as vent mount or window suction cup mount as well. The spacing of the prongs at the bottom is wide enough that the USB port isn't covered, so I can easily plug it in for long drives. 1 Quote Link to post Share on other sites
EskeRahn 5,460 Posted March 17, 2020 Share Posted March 17, 2020 2 hours ago, wilhelmfitzpatrick said: I like the gravity style holder for quick placement and removal. It seems to be available as vent mount or window suction cup mount as well. I like this design too, very practical. It exists for landscape too. See above 🙂 Quote Link to post Share on other sites
lzb 43 Posted March 18, 2020 Share Posted March 18, 2020 In my previous car, I used the iBolt mount system for the device I used before I got the Pro1. It's nice because it holds it at the top edges, so it doesn't interfere with the buttons. It has a universal design, so the holder (I used the sPro 2) itself can be mounted different ways. You can create a custom solution here . I can't speak to its performance when the Pro1 is open, but personally I would never use it that way anyway Quote Link to post Share on other sites
Muth 132 Posted March 22, 2020 Share Posted March 22, 2020 On 12/28/2019 at 6:58 PM, Rob. S. said: I guess this would be a case for a 3D printer. Unfortunately I'm not really into that... So, I give it a try. I draw something like that : To be hooked in the ventilation blades 4 1 Quote Link to post Share on other sites
Muth 132 Posted March 22, 2020 Share Posted March 22, 2020 I used Fusion360: Printed on a Prusa I3 mk3: 6 1 Quote Link to post Share on other sites
Muth 132 Posted March 22, 2020 Share Posted March 22, 2020 Seem functional 5 2 Quote Link to post Share on other sites
Muth 132 Posted March 22, 2020 Share Posted March 22, 2020 And adapt quite well 10 1 Quote Link to post Share on other sites
Muth 132 Posted March 22, 2020 Share Posted March 22, 2020 3D Files are here : https://www.thingiverse.com/thing:4236222 (thingiverse is quite slow today) 10 Quote Link to post Share on other sites
Rob. S. 1,661 Posted March 22, 2020 Author Share Posted March 22, 2020 Wow, not bad! 🙂 1 Quote Link to post Share on other sites
altwouss 22 Posted March 23, 2020 Share Posted March 23, 2020 On 3/17/2020 at 2:46 PM, Rob. S. said: Unfortunately, I still don't even have the phone... My plan is to try the 711042 Brodit holder I already have, as the period for returns is long since over, and if it doesn't work out, I'll order the 511309 Brodit holder, too. Oh I am sorry that might have been naive or inconsiderate on my part. On 12/30/2019 at 7:24 PM, mosen said: The universal holder from Brodit does the job. Sorry, no idea about measurements and order number, it is like 6 years old. But i just needed to widen this universal holder to max after using it for XA2 which was more narrow. The thickness is exactly matching the cutout space so the pro¹ sits very tight.https://twitter.com/eLtMosen/status/1197074326245257216 Oh, and cheers form an Audi 80 [B4] owner for ~10years 😄 Now i upgraded to this nice [W639] Vito with just 260tKm. I think I am going with the 511308 (https://www.brodit.com/product.html?id=511308). I have the phone and have been measuring with a caliper. The phone is 10mm thick at the edges and until ~5 mm from the edges its max 13mm, at it's thickest it's 14.3mm (with screenprotector). The description and picture from mosen exactly match the fit I am expecting with 511308. I am going to order one. Quote Link to post Share on other sites
EskeRahn 5,460 Posted March 24, 2020 Share Posted March 24, 2020 I think the gravity idea is the best. Unfortunately most only do either landscape or portrait. And the landscape ones are not that common out there. I have found just two claiming to do BOTH though. I found this but also this kids friendly design. For both I assume the feet needs to be modified for the USB plug in portrait The pure landscape I only found in one version, e.g. sold here. Many of the portrait ones will interfere with the buttons and/or the USB plug, so a bit of search and trial&error can be expected. Ordered this. 2 Quote Link to post Share on other sites
altwouss 22 Posted March 26, 2020 Share Posted March 26, 2020 (edited) So I got the holder, as you can see the buttons are fine with this one, you may need to be careful with the camera button though. You can even use the fingerprint unlock. So 9-13mm might still be a bit too much. I am going with it, as the room is only minimal I might fill the edges with some rubber feet I have lying around. But @Rob. S. yours might fit exactly. Edited March 26, 2020 by altwouss 2 1 Quote Link to post Share on other sites
Rob. S. 1,661 Posted March 26, 2020 Author Share Posted March 26, 2020 2 hours ago, altwouss said: So 9-13mm might still be a bit too much. I am going with it, as the room is only minimal I might fill the edges with some rubber feet I have lying around. But @Rob. S. yours might fit exactly. Thanks! Might be a good thing then that I wasn't able to return mine anymore 🙂 Quote Link to post Share on other sites
EskeRahn 5,460 Posted April 17, 2020 Share Posted April 17, 2020 On 3/24/2020 at 9:03 AM, EskeRahn said: . Many of the portrait ones will interfere with the buttons and/or the USB plug, so a bit of search and trial&error can be expected. Ordered this. Got it in the mail today, and well it is not a good fit, but not hopeless either- with suitable modifications. On the plus side the the two feet on the button side lands perfectly around the fingerprint scanner, and not touching the power button. On the minus side one of the bottom feet sits right over the usb plug, but it will work practically equally well if you cut that one away! The rubber feet are designed for grabbing a thinner phone, but are just put over a 15mm long plastic pin, and can easily be pulled off and then remounted a little further out. Either glued on or remounted with a piece of paper or the like around the pin to tighten the fit. Quote Link to post Share on other sites
EskeRahn 5,460 Posted May 12, 2020 Share Posted May 12, 2020 On 3/24/2020 at 9:03 AM, EskeRahn said: . . I have found just two claiming to do BOTH though. I found this . Just got the above in the mail today, and it is a good fit in both portrait and landscape AND has the benefit mounted in a car to fit almost any phablet with a short edge between 64 and 88mm. To use while charging in portrait, I will suggest to make a small cut in one of the feet. (Note that in portrait the 'toes' does not catch the edge of the display-part of a Pro1, but it still can not fall out) Quote Link to post Share on other sites
EskeRahn 5,460 Posted May 19, 2020 Share Posted May 19, 2020 On 5/12/2020 at 11:42 AM, EskeRahn said: Just got the above in the mail today, and it is a good fit in both portrait and landscape AND has the benefit mounted in a car to fit almost any phablet with a short edge between 64 and 88mm. Same model now available on ebay from a few vendors e.g. https://www.ebay.co.uk/itm/274365634322 Quote Link to post Share on other sites
Acurus 17 Posted May 30, 2020 Share Posted May 30, 2020 My first posting here! Today I ordered the "f(x)tec pro1". In the past, I was a heavy user of every Nokia Communicator. Till 2018 I used the N900 (have had three!). Actually I am using a Blackberry Priv. Every of my mobile phones has had it's own active car holder. In the last 10 years I used them from "Brodit". There are active universal holders from Brodit, but they will not work with the "f(x)tec Pro1", because the USB slot is not in the center. Therefore I asked Brodit today, if they are planning to produce a type-specialized active holder for the "f(x)tec Pro1". I hope, they will. An I hope, others will, too. Because I will not use passive car holders with all the cables ... Therfore it would be nice to change infos here, which car holders are beeing used and how they work. Quote Link to post Share on other sites
Craig 1,435 Posted May 30, 2020 Share Posted May 30, 2020 Some people already discussed this, you may wanna check out their thoughts. https://community.fxtec.com/topic/2585-which-car-holder 1 Quote Link to post Share on other sites
EskeRahn 5,460 Posted May 30, 2020 Share Posted May 30, 2020 7 hours ago, Craig said: Some people already discussed this, you may wanna check out their thoughts. https://community.fxtec.com/topic/2585-which-car-holder (Thanks, merged it in) Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.