EskeRahn

I hope you are right 😁 Though we never found a way to consistently trigger the bug, so hard to say for sure. Has anyone that updated to 20220711 seen the charging-bug since? Bad news: Just managed to trigger it...... (at 67%) What I did was: In unlocked state, Plugged, unplugged and replugged a few times Locked, waited three minutes (while it was charging on a table). Picked it up and unlocked the device with fingerprint Unplugged and replugged Tried to do exactly the same after a reboot, but it did NOT trigger it again, so not a consistent method, Tried

He he. If so I doubt things would work as relative well as they did... Especially the camera But is a bit odd that it is 'released' in a state where I can not even do a clean wiped GAPPS-free flash and boot it.... So I assume that in special conditions an upgrade might work. An obviously thing to try would be a clean gapps-free wiped AICP-R and then do a AICP-S flash without wiping. I have not tried that (yet?) Tried, no cigar...

See this thread for working install: ---------------------------------------------------------------------------------------- Below is initial attempts where I used a wrong boot image Using this AICP.S mage aicp_pro1_s-17.1-WEEKLY-20220713.zip I was super optimistic and went from 16.1 with OpenGapps to 17.1 and MindTheGapps 12 in one go, without a factory reset (=wipe). ...and that did not go well,,,, I got a boot-loop (I used the recovery-image from Lineage lineage-19.1-20220711-recovery-pro1.img) Then did a factory reset, and it booted - obviously with

Aicp S-17.1 now available, though not really working (yet?).... See

(on the wiring, the two shifts and the two ctrls are physically wired pairwise. so though we see 66 keys, there are only 64 distinct keys)

Indeed and remember that some have preordered not perked for a Pro1X, and we have no knowledge on how these two lines are interwoven, but I guess they all come after the Pro1 orders, if things goes by chronology....

(lineage-19.1-20220711-nightly-pro1-signed.zip on June 5 security patch installed smoothly using adb sideload and MindTheGapps-12.1.0-arm64-20220605_174313)

(lineage-19.1-20220704-nightly-pro1-signed.zip on June 5 security patch installed smoothly using adb sideload and MindTheGapps-12.1.0-arm64-20220605_174313)

Same here. It could be unfair, but I have the feeling of Magisk like a can of worms I avoid to install.

The keyboard itself seems very close to identical to the Cosmo, and some have wrote about using that in here. If i recall correctly you can do thumb-typing. ADD: Here two report it in a non-positve way as too large for it

Peronally I have long been advocating for one hand operability, and this means a limit around 65mm wide. BUT there are two drawbacks on that. One is lesser keys (or for me worse: fewer). Secondly the display would be lesser, and that again would mean less information (=a lot of scrolling) or the use of a font so small that it gets beyond what my aging eyes can handle without extra glasses. Also remember that the newer ugly material design wastes more screen space, so many apps are today designed for the oversized phablets and not phone-size (quite similar to a lot of apps working poorly i

The principal difference keyboardwise (apart from the opening system) is that Pro1 got more but minor keys. So I expect what is the best for a specific person depends on if they need A-Z (almost) only, or have fingers that struggle with small keys, if so the larger keys are likely to be a plus. If you on the other hand want national letters and other keys in their standard positions the Pro1 is likely to be a better choice.

would be great if the niche products could find ways to help each other, as they target different parts of the small keyboard segment. But the big question is if the visions are compatible?

The second i've heard mentioned before. The first is new to me. Before the obvious suggestion of a factory reset, you might try to do a very long power-press, (about 10 sec) it seems to do a deeper reboot than just the ordinary 'restart'.

Glad you found a workaround. but odd indeed.

odd, the combo works fine here...

(If I do not recall incorrectly it has been quite a while siince Fxtex asked us to double-check the address - was actually surprised that Unihertz did not ask us to confirm our address but to reenter it...)

well they (unihertz) just asked us for our addresses, so likely a close run....

A, sorry, then please ignore the last part. A factory reset could still do wonders if a bad flash has messed up things.

The big question here is if you can get the key-tops free of the elastic plate? The current is some combination of an elastic mat, and some harder material on top, that is then painted white (and for some keys a colured square top right, and finally the black layer of paint. And this combined plate can be freed by heat. I have no knowledge wether the tops can be separated by heat, Though I intuitively doubt it... So you might need to 3D-print the elastic base plate as well in e.g TPU On my spacebar the black is wearing off, all other keys are (still) intact. So the timing of soo

(Smoothly installed aicp_pro1_r-16.1-WEEKLY-20220629.zip on June 5 security patch and open_gapps-arm64-11.0-pico-20220503.zip using adb sideload)

(lineage-19.1-20220627-nightly-pro1-signed.zip on June 5 security patch installed smoothly using adb sideload and MindTheGapps-12.1.0-arm64-20220605_174313)

@pebert I would advice to factory reset. But as @Hook suggested try with a flash first, and if that does not fix it go for the reset. You are mentioning Magisk, and If I understand correctly, some things are principal different in that aspect going from 18 to 19.

Interesting! Killing AudioFx dos not do the trick here by it self. Disabling AudioFx and restarting, does not change anything either. (*) So it must be viper that does 'something' on yours.... (have not installed it) (*) ADB shell pm disable-user org.lineageos.audiofx ADB shell am force-stop org.lineageos.audiofx ADB shell pm clear org.lineageos.audiofx And after that did not work reenabled it with ADB shell pm enable org.lineageos.audiofx

I can confirm, only the speaker near the usb-plug is active with LOS 19 on the Pro1.