EskeRahn

Could be worth a try, but as is all plastic (well less the cardboard stiffening) it should clearly by done by caution. But it COULD soften the glue. Will try with on one of the lesser fortunate attempts 🥴

I just ordered some of these

Ah I see, yeah, bad handling på DPD there 😥

As a cheaper solution than making a new input method, perhaps we could let UIOP, JKL.... match the twelve. That is Sym+U would match the top left symbol etc. 🙂

Have you got a link by any chance 🙂

Yes, a build in option in Pie, Not all app supports it though. In the task.switcher tap and hold the icon above, and there can be an option "split screen"

Yes, that was my point. They OUGHT to have a way to (b)lock the change-option when they can no longer handle a change.

Ah, I see. This one is fairly easy to split. If you go for the black or blue, the debris left is much less noticeable than the 'yellow'. And it is ONLY noticeable when folded FULLY open.

Now that was a really helpful hint. Never even considered that a surrogate-keyboard app would be hardware keyboard aware. Good job Swiftkey! Will try some similar to see if they can do the same, and perhaps (even) better.

(If you do not want to be disturbed, use aeroplane mode. Quick to turn on/off and saves battery)

I see, but when glued why then this over others that will be thinner?

My guess would be that they 'simply' lack a way of 'locking' this option down, once the parcel is close to delivery. Of course optimally it would work until the last second, but I can see the logistic problems in that, especially if on the van and with a planned route.

That 227 is interesting, as we know the highest before this was 225. So the cut is now established much narrower towards the lower end. And we can do better estimates within the accuracy of this "six" and "70" we now know the total most be in the order of 2250. This can now be narrowed down to anywhere between 225/.13 and 226/.09 that is in an interval about 1750 to 2511. So we would expect a highest serial number no lower than 1225, the highest yet reported is 1011 though.

I contacted them, they got it in black too, but out of stock. But note that the magnet might be too weak see the warning here Also look closely at this, the camera hole is quite deep to accommodate for the magnets, so the whole thing is thick, and it MIGHT be a problem when we need to expand the hole for the camera and LED...

Should be easy to spot opened, At the bottom part where the screen sits, about 3cm from the sides.

I wonder if this is a Pie bug, as the whole thing is so close to stock andoid? Do we got anyone with stock android on a 2160x1080 device that can check?

If you get the same with different cables it sounds like a faulty unit, contact support.

Odd I have been using MTP only from day one, never had an issue, and I see both internal and SD (if I give it an SD card) Could it be some of the protocol issues with the above 32GB cards you have talked about in other threads that are teasing you here also? There COULD be some limitations in MTP perhaps ???

Oh dear this thread is exploding into a mess of individual devices hardware issues and general issues.... Sigh.... hope another mod has the time to clean it up...

Well nothing is going to happen before the end of CNY, and the virus thing is also likely to cause delays. But once started I would guess they would need a couple of weeks to do the remaining. So unless they are short on some components for new orders, and just extend the current remainder, I think that your estimate sounds fair.

Well ebay is the easy choice "Self adhesive felt" But for a physical store I would ask somewhere they sell either a DIY-stuff, silverware, jewels or furnitures, as it is often used in drawers for cutlery or jewel boxes. (though here often in red or green)

It already 'lands' on some rubber bumpers, I would suggest to open it with your index finger on (or catching) the back edge when you push with your thumb. OR use gravity(!). See this

Another more silent way is to pick it up holding the screen, pushing the bottom down with the middle finger. This can be combined with pushing at the fingerprint scanner unlocking it. (it is dampened by gravity, and stopped by the thumb) YouCut_20200129_120706253.mp4

Ah! that was what I was trying to show in the first slo-mo video. But not very good I'm afraid. 😥

Never be tricked on 100% on a phone. If you want to measure start from e.g. 99%. It is a long story to the why, but 100% covers a range of remaining capacity And anyway the percentage is always an ESTIMATE, not an absolute measurement like the voltage. See my blah blah on that here (about half way in) with this: