Parhelion 114 Posted October 31, 2019 Share Posted October 31, 2019 I was imagining a polymer cup with thin metal clamps moulded in to grab the edge of the lower part of the phone without impeding the slider, to be used as a protector on itself, or, my preference, as a base for a leather sideflip. But no idea how to get a company to produce something of the like, and whether the clamps might interfere with antennae. 1 Quote Link to post Share on other sites
EskeRahn 5,464 Posted October 31, 2019 Share Posted October 31, 2019 Actually it COULD grip over the two back corners, some 20x20mm, as long as it is not more than some ½mm thick, worst case it would make the device ever so slightly thicker closed. So that could be a way to do it... Quote Link to post Share on other sites
Gon009 70 Posted October 31, 2019 Share Posted October 31, 2019 (edited) After seeing that they admitted that case doesn't exist after they already maybe started shipping phones... I would never imagine that they would fall down that much... Sleeve is useless. Case at least is there to take some amount of the impact if the phone drops. Of course all drops will be accidental, because of haste, lack of attention. To use the phone you must take off the sleeve, before that operation there will be little chance for phone to be dropped unless someone has a hole in pants pocket. In my opinion, sleeve could be only useful if one wants to hold a phone in a pocket together with keys or other sharp objects(I don't even plan doing something like this), in every other situation it will be useless... Edited October 31, 2019 by Gon009 3 Quote Link to post Share on other sites
EskeRahn 5,464 Posted October 31, 2019 Share Posted October 31, 2019 23 minutes ago, EskeRahn said: Actually it COULD grip over the two back corners, some 20x20mm, as long as it is not more than some ½mm thick, worst case it would make the device ever so slightly thicker closed. So that could be a way to do it... Tried with some thick paper (a ½mm thick booklet). And a case can actually grip over the entire ends, so this should be possible keeping the long edges free, so you can open the device by either pushing the front or lifting the back edge after your preferred operation mode. So I think a stiff bottom (e.g. leather) and 5mm black elastic bands on both sides of the keyboard would work. Quote Link to post Share on other sites
EskeRahn 5,464 Posted October 31, 2019 Share Posted October 31, 2019 The bottom part has dimensions really close to a Samsung note 7 (153.5 x 73.9 x 7.9 mm) so I think I will try to find a leather case for that, and see what I can modify... ADD Or "Note FE", same dimensions 3 Quote Link to post Share on other sites
Raksura 270 Posted October 31, 2019 Share Posted October 31, 2019 Thank you, I was wondering what the height of the keyboard part was. Difficult to find a match without that. Sounds like it would look much better than what I had in mind. We would just have to cut out the borders where the buttons don't match and a different hole for the camera/flashlight, which is definitely doable on leather + plastic. 1 Quote Link to post Share on other sites
david 929 Posted October 31, 2019 Share Posted October 31, 2019 1 hour ago, Gon009 said: After seeing that they admitted that case doesn't exist after they already maybe started shipping phones... I would never imagine that they would fall down that much... Sleeve is useless. Case at least is there to take some amount of the impact if the phone drops. Of course all drops will be accidental, because of haste, lack of attention. To use the phone you must take off the sleeve, before that operation there will be little chance for phone to be dropped unless someone has a hole in pants pocket. In my opinion, sleeve could be only useful if one wants to hold a phone in a pocket together with keys or other sharp objects(I don't even plan doing something like this), in every other situation it will be useless... I agree that a sleeve and a case don't serve the same purpose and it was dishonest of them to keep silent until the phones started shipping in order to notify everyone that the case is no longer being made (regardless of whether it is free or for sale). Quote Link to post Share on other sites
EskeRahn 5,464 Posted October 31, 2019 Share Posted October 31, 2019 5 minutes ago, david said: I agree that a sleeve and a case don't serve the same purpose and it was dishonest of them to keep silent until the phones started shipping in order to notify everyone that the case is no longer being made (regardless of whether it is free or for sale). For a laugh go to the "Shop". The "Hard Case" is still there as "Coming soon"... 🙄 1 Quote Link to post Share on other sites
david 929 Posted October 31, 2019 Share Posted October 31, 2019 8 minutes ago, EskeRahn said: For a laugh go to the "Shop". The "Hard Case" is still there as "Coming soon"... 🙄 😐 Maybe that refers to their belief/hope that some 3rd party will make cases for their phone that work, when they couldn't figure out how to do it. 😏 To be fair, a company that specializes in cases might be able to do that, since that's their business. And, I suppose, with a start-up, those companies aren't going to make them before the phone is released. It will be interesting to see if anyone does make anything for it, given the lower production numbers vs other phones. On the other hand, if *most* Pro1 customers will buy a case (since there isn't any other competition), then it might be worth it to them to produce cases for the Pro1. 1 Quote Link to post Share on other sites
_DW_ 628 Posted October 31, 2019 Share Posted October 31, 2019 https://www.amazon.co.uk/Hairyworm-Personalised-Samsung-leather-Personalise/dp/B07FQHNHJH Need something like that holder (bottom picture) which has a strong elastic bit over, is that what your saying might be possible @EskeRahn? Quote Link to post Share on other sites
EskeRahn 5,464 Posted October 31, 2019 Share Posted October 31, 2019 24 minutes ago, _DW_ said: https://www.amazon.co.uk/Hairyworm-Personalised-Samsung-leather-Personalise/dp/B07FQHNHJH Need something like that holder (bottom picture) which has a strong elastic bit over, is that what your saying might be possible @EskeRahn? I meant something that went over the top and bottom, e.g. clear plastic strap, rubber band or elastic band. The Note 7 has fairly large top/bottom bezels. Many years ago, this was a common way to do flip-cases for pocket calculators and pocket multi-meters, so with a little luck it exists for the Note 7. Like the blue bands of this quick mockup Quote Link to post Share on other sites
mcdinner 375 Posted October 31, 2019 Share Posted October 31, 2019 38 minutes ago, EskeRahn said: For a laugh go to the "Shop". The "Hard Case" is still there as "Coming soon"... 🙄 Shipping was also early october until end of october 🙂 Quote Link to post Share on other sites
KingOfTerrible 69 Posted November 1, 2019 Share Posted November 1, 2019 17 hours ago, mcdinner said: This is sad as a sleeve does not help to secure the phone when dropped while holding it. Phone won't drop while in my pocket and scratches on the back are not the thing I'm afraid of. Also this is again a communication fail, as the last information from June!! was that there would be pictures soon of the case. Now there is no protection at all, and If the phone manufaturer itself cannot create a case who will then ? This may be a problem of this shitty borderless designs which came up the last years. On my E7 I had a hardcover like this, which I would like to see again. I'd like to see a case like this too, worked well to protect my e7 front and back from damage while still allowing the phone to be fully usable. 1 Quote Link to post Share on other sites
Siani_8 105 Posted November 1, 2019 Share Posted November 1, 2019 Final version of the Pro1 case! 5 Quote Link to post Share on other sites
Doktor Oswaldo 904 Posted November 1, 2019 Share Posted November 1, 2019 6 minutes ago, Siani_8 said: Final version of the Pro1 case! This is clearly the case of the xiami mi mix 4: 2 Quote Link to post Share on other sites
Siani_8 105 Posted November 1, 2019 Share Posted November 1, 2019 1 minute ago, Doktor Oswaldo said: This is clearly the case of the xiami mi mix 4: God I hadn't even thought of how much of a nightmare making a case for those folding phones would be lol Quote Link to post Share on other sites
netman 1,424 Posted November 1, 2019 Share Posted November 1, 2019 1 minute ago, Siani_8 said: God I hadn't even thought of how much of a nightmare making a case for those folding phones would be lol That Xiaomi one does not even fold, it's permanently folded basically. And notice there is 0 physical buttons on it 😥. 1 Quote Link to post Share on other sites
Doktor Oswaldo 904 Posted November 1, 2019 Share Posted November 1, 2019 Just now, netman said: That Xiaomi one does not even fold, it's permanently folded basically. And notice there is 0 physical buttons on it 😥. And luckily it will not be released 1 Quote Link to post Share on other sites
Siani_8 105 Posted November 1, 2019 Share Posted November 1, 2019 2 minutes ago, netman said: That Xiaomi one does not even fold, it's permanently folded basically. And notice there is 0 physical buttons on it 😥. Didn't even know that was a thing. I generally don't pay much attention to new/upcoming/potential devices unless I see a KB lol 1 Quote Link to post Share on other sites
netman 1,424 Posted November 1, 2019 Share Posted November 1, 2019 2 minutes ago, Doktor Oswaldo said: And luckily it will not be released They're saying there will not be a Mix 4, but the Mix Alpha is what that thing in the picture is... https://www.mi.com/global/mi-mix-alpha 1 Quote Link to post Share on other sites
Doktor Oswaldo 904 Posted November 1, 2019 Share Posted November 1, 2019 Just now, netman said: They're saying there will not be a Mix 4, but the Mix Alpha is what that thing in the picture is... https://www.mi.com/global/mi-mix-alpha Oh sorry got confused. These slabs are looking all the same? (Hopefully netman will buy that one) Quote Link to post Share on other sites
netman 1,424 Posted November 1, 2019 Share Posted November 1, 2019 Just now, Doktor Oswaldo said: Oh sorry got confused. These slabs are looking all the same? (Hopefully netman will buy that one) I've been demanding they add a keyboard and threatening to cancel my pre-order if they don't, but they don't reply :-/. 5 Quote Link to post Share on other sites
Doktor Oswaldo 904 Posted November 1, 2019 Share Posted November 1, 2019 Just now, netman said: I've been demanding they add a keyboard and threatening to cancel my pre-order if they don't, but they don't reply :-/. Maybe because you don't have a preorder? 2 Quote Link to post Share on other sites
netman 1,424 Posted November 1, 2019 Share Posted November 1, 2019 Just now, Doktor Oswaldo said: Maybe because you don't have a preorder? shhh 1 Quote Link to post Share on other sites
Siani_8 105 Posted November 1, 2019 Share Posted November 1, 2019 I already have a nice handmade leather pouch for the Pro1 but I wonder if there was enough of us for a "group buy" if a phone case company would be interested in designing a hard case. I assume they would need a phone in hand to do that? Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.