CornholioGSM

...exactly as you say...thats why i hate c connectors...and work on it. Sometime are pads too smashed and is impossible to make bypass for all missing pins...then is solution made bypass only for data and charging. On removing...use around 330celsius and head connector from top...it must be really fully released. If is near microphone, then cover it with kapton tape and if mic have hole on another mobo side then cover this hole too...mic can be smashed really quickly with hot air! ...then remove all old tin from holes for connector frame.Put new tin on all pads(same amount - not

it is possible to change it 🙂 .....but sometime i have problem, that i customer have broken / missing pins....then is it littlebit harder and is needed to made new ways with enameled wires.

Looks like this connector have hidden one row of pins...it must be soldered with hotair or infrared. ...post photo of another side...are visible pins? you have visible 6pin - gap - 6pin correct? Check my pic what i mean EDIT...check this :

...simple...put phone to preheater, set it to 80ºC for 1min....and then use foil for cut display 🙂

I cannot reccomend t-8000 or any t/d-8000-7000 etc glues. They have problems on sumer temperatures 😞 If you are in europe, then buy pattex 100% gel....by me is tested on hundreds phones 🙂 if you want something more and more better, then you must buy glue for car windscreen....it is really best, but is with it bad work you will be really dirty 😉 ....soo pattex

...please post photos

Margins was set to 0...now i have set 16...i must test it

hmmm...i have question. My phone runs on aicp rom and i have problem with something like low respond on swipe - unlock phone etc. I have manytime problem with unlock...i must swipe slowly . All others works fine...i can touch without problem on any place on screen. Can it be display problem .... or maybe aicp problem?

....it is hard with displays...on ali will it be always cheaper, but nobody can promise you new display without missing pixels on corners 😞

Hmm...because i dont have problem with charging for approx 14 days....was this problem solved? ...it looks like all is without problem...i can charge without reboot

...can you post photo of battery connector and connector on mainboard ?

...post here pics of board with c connector

...."deglue" display from frame is simple. I have preheater for it , sometime i am too lazy to go to second room where is preheater 🙂Solution is simple - buy zippo lighter fuel, littlebit moisten gap between lcd glass/frame...and then use carefully razor blade and put it between glass and frame - but not cutting! ...thats all. Edit - razor blade is needed because is thin!!!

hello all, ....i still have little problem of no internet connection on some apps - mainly on gmaps, translator and sometime on messenger. I really dont known what to check...maybe it is problem on battery optimization but i dont known. After reboot phone all works fine for maybe one day...and then again no internet connection. I can be on lte or wifi but problem same.....and sometime same problem on updater too. Any idea?

...i have little problem. always after two days on battery - when is battery on around 20% and when i connect charger phone says "plugged in, can't charge right now". After reboot is all fine...i can reconnect charger many times and always charging On old aosp rom was all fine

oooh ok...so maybe is missing whole baseband...just like on live demo units 🙂

hmmm....just question... it lacks only antenna it means that prepro have different back cover?....but hw is same?

...it looks like whole development of new roms is dead 😞

Hmmm i mean that boot animation can be only in portrait...orientation sensor is enabled after fully booted os. ...you must made something like orientation neutral animation....like rotating logo on center 😉 edit....badly written...you can made animation in landscape or portrait....but orientation is fixed

Btw...just for interest...some android kernels can use boot animation with boot sound. You can test to search motorola droid r2d2 boot animation dump

...yesss you can replace it 🙂 just create bootanimation.zip , set permission to rw-r-r and reboot 🙂 ...here are some from xda user @mauam https://drive.google.com/drive/folders/1RpFcoEWYsRt2MX7FotKcLICqYq6l5MFY

@DieBruine wrong and wrong 🙂 1) microphone is not on top display part - microphone is 1cm right near usb connector (small hole). 2) here is nothing to bend for better mic contact. Mic is digital (4-5pin) and is soldered directly to flex/pcb. What can be bad...flex cable connector (i mean flex cable to usbc,speaker ect) can be littlebit disconnected on mainboard (I do not think so), or microphone can be fall down after phone fall to the ground , or can be damaged ( water, dust etc). Solution...solder new microphone...if it doesn't help will be needed to check aud

I have misterious problem. My volume keys stopped working with off screen on all apps - youtube, eleven player etc. I can still control next/prev. song with long press. When screen is on all works fine? I have found only " volume rocker wake" .Anyone have idea how to fix it?

...maybe with resistor wire and then quick colddown ? ...maybe

Yesss...they can be madded , but does not exists now. Similar glass is for s9+ but is too long