Noir

Well, kind of expected with the current Build of LMODroid I guess Source What about the better Desktop-Mode adaptions they are talking about, anything special there? I guess the more interesting Build will be ... soon™

Nice find. Unfortunately the seller does not offer shipping to my region, I contacted him nevertheless if there is an option, i'll edit this post when I receive an answer. edit: response was not too good, "if you can't buy it I can't ship it.". I'm not sure how the seller would respond to a request to buy it outside of aliexpress, but I did not ask further.

I'd happily take one. DM me Please.

They are just bare cells without the BMS PCB and connector to the Pro1. you would need to transfer them from your original board to make them fit. I am very sure that the cell´s sizes are identical to the pro1 and the pro1x, so those cells could be used on either of them as long as you transfer the respective board from your old battery. keep in mind that this is not really a rookie-job and you can easily mess up things, nshans way looks not very durable. But sure, for a Proof of concept it might be just fine.

I'd buy one cell from you if you'd be interested. I would try it out on my Pro1-battery, and I do have a spot-welder to replace the BMS board the way it's meant to be done. 🙂

I can confirm this working. I am able to install the display driver on the replacement screen attached to my pro1 and then it is working as expected on the Pro1x.

Unfortunately I experienced the same issue as you are describing, for me it is a hardware issue. The Keyboard-Flex cable was bent too sharply under the battery and cracked. There is no way to replace that without tearing apart the glued keyboard. I was recommended to get the whole keyboard-faceplate replaced.

Had this Issue on a Huawei P20 Pro before - fingerprint sensor getting hot, due to that fast discharging battery. Disconnected the connector aswell to save costs. Just want to point out, that I would not blame F(x)Tec for that fault, defects like that can occur. (imagine this happening on an 🍏7/8..)

Hm, for me and Stock QWERTZ it works fine, Shift+ß for ? (like on a real keyboard), although other yellow symbols are used with the yellow arrow (like alt on a traditional keyboard if you want to look at it like that..). I can not really reproduce your issue there. On early builds there was acutally a mis-mapping (` for example was a lookalike), but ?/ß was not one of them.

QWERTZ setup instructions is the pinned post. I will attach screenshots due to not having too much time currently of my o2 settings and status, also the mentioned slider settings. Maybe you just missed that option in the settings menu. Auto rotate via quick settings is enabled. some apps refuse to turn landscape or ignore orientation lock, but that is only for a few.

QWERTZ #321XX stock assigned mail today.

Germany, 20km from Brunswick / about an hour from Hannover

the right part of my screen does not touch the landing pad either, it´s exactly as in the picture above. But I don´t have that rattle when typing, only when i shake the phone up- and down quickly. (just did that only to verify the posted issue). only when I hit the keys unnaturaly with my thumbs i can get the rattle to occur while typing, but usually i don´t even lift my thumbs from the keyboard while typing.. I expect the rattle to change over time, either through wear or debris which makes the movement harder, not sure if it will become worse or better.

Any influence on the display when opening/closing the pro1 slowly and turning the display off and on on different opening levels? It´s mandatory to turn off the display and reawake the phone after each movement of the slider. Maybe you´ll get a working image doing that to troubleshoot the flex cable, it´s connection, or the screen itself..

Had the same issue, as told as the others. Charge your device. update will stay at 100% without any error message, needs 40% charge to finish the update. last resort: system->apps->show system apps->software update->clear storage->force stop Redownload the update then. if your battery is well above 40% and plug charger.

Sure. To access the factory test tool (within the stock rom of course), enter Settings -> About Phone -> Anroid Version. You will be presented with a popup, scroll down there and tap 3 times quickly on the build number: The options below are proximity- and Ambient light sensor test. To you and others: be careful with the others. One option dials emergency without any further warning! The two matching tests are checked on my screenshot: edit: You ninja-edited your post. have you tried turning it off and on again?

The rest of the pre-orders is scheduled to be produced after the end of CNY, meaning a new batch should be ready mid to end of February.

This behavior is the same on the stock build, and was raised to the CEO when I had the chance to get a hand on a prototype last year. I will try to bring this to attention again, but it's not a lineageOS specific thing as of now.

can confirm, but I highly doubt it´s a Pro1 specific issue. To get those spell checking red lines under the bad words i needed to enable spell checking via gboard itself and also allow some privacy settings within chrome, then I had the empty box aswell. Maybe someone more into Google Apps can help, in the meantime try clearing Data and Cache of both Chrome and Gboard and confirm your settings regarding region and languages.

Can not confirm. Assuming you mean the same as I do. Please provide more information to reproduce your issue.

Will give you mine for exchange, it´s a one-of-a-kind. I would not recommend to take it apart to peel of the button and reseat it. As far as I can tell, single Buttons are not meant to be replaced/torn off.

325

thanks alot @tdm for your work, has anyone tried to use microG with this build? I am not experienced with microG, but I am trying to gain some knowledge about it. Having admitted that sorry if this question is unnecessesary, but maybe an answer is possible nevertheless.

tracking number received, Fxtec Order Status 'Completed' Delivery scheduled for friday, which is very shortly.

Kind of, yes, and we all had access to the picture of the Pro1 in pieces Chen posted on twitter, which helped a bit. Due to my work-background I'm very used to disassembling phones.